ZellmerBreen379

We’ve been anxiously ready for the discharge of Makita’s 40V max XGT line. If you have any thoughts pertaining to exactly where and how to use drill bits (try this), you can get hold of us at the website. Focused on higher performance than a lot of the 18V LXT products, we expected to get extra out of the Makita 40V max XGT hammer drill. As a comparison, we examined the GPH01 hammer drill aspect-by-side with their flagship XPH14 from the 18V line.


- Outstanding 2600 RPM high pace

- Plenty of muscle with 1250 in-lbs of torque

- Excellent ergonomics and handle design

- Smooth operation with almost no runout

- Kickback management

- Electronic clutch


Cons


- Battery isn't backwards suitable with 18V LXT instruments


Makita 40V Max XGT Hammer Drill Review Performance


Makita geared this hammer drill for increased speeds than most drills in each first and second gears. The decrease pace runs at 650 RPM whereas the higher gear tops out at 2600 RPM. That top speed matches up with 39,000 BPM to make your masonry drilling extra environment friendly. Wrapping up the specs, the GPH01 matches the XPH14 with 1250 in-lbs of torque in low gear.


As at all times, we want to see how that translates to work, so we ran just a few checks to find out. Starting with the PTR carbide drill Test Track, we ran these assessments alongside the XPH14. Check out the video here.

If you’re not aware of the PTR Drill Test Track, here’s what it entails on a 2×4 stud:

Test Track Sections


- 20 drywall screws

- 10 x 1/2 twist bit holes

- 10 x 3/4-inch spade bit holes

- 10 x 3/4-inch auger bit holes

- 1-inch gap noticed

- 2 1/8-inch hole saw


Because the mud settled, the Makita GPH01 confirmed XGT’s greater efficiency by ending in 1 minute, fifty eight seconds-17 seconds sooner than the 18V LXT XPH14! That finish was also fast enough to drag into second place, just 2 seconds behind Flex in first place.


Moving over to concrete, we ran 1/4-inch and 1/2-inch concrete bits. Makita’s 18V hammer drill wanted an average of 5.23 seconds and 6.Eighty five seconds, respectively. The Makita XGT hammer drill was considerably quicker, averaging 4.Forty four seconds and 5.34 seconds.


Finally, we decided to see what happens if you happen to try to tough in 2 9/16-inch holes with a self-feed bit. The 18V hammer drill had to remain in low gear for all of its holes, averaging 5.53 seconds. The XGT was ready to start out in high gear, cobalt drill bits but wanted to drop into low after the first couple of holes introduced it from its max to nominal voltage. Its closing common was more than a second faster at 4.Forty four seconds.


One thing we seen through the course of our testing is how smooth the drill operates. Makita usually has very low runout (wobble) in their drills, and that’s the case with XGT as well.

Makita 40V XGT Max Hammer Drill Review Design Notes

18V LXT Vs 40V Max XGT Power Source


One of the very nice issues about shifting up to the 40V max XGT line is that the batteries aren’t much greater than the 18V LXT ones. The footprint is slightly bigger and it’s about 4 ounces heavier, but they’re sticking with the 10-cell pack as the foundation. The obvious distinction is that the 18V pack is 5.0Ah and the 40v max XGT pack is 2.5Ah… but they've the identical 90Wh capability.


Inside, it’s completely different. The XGT line has a distinct electronics bundle, more energy potential, and even a more durable build. Makita’s tagline is to "outpower, outsmart, and outlast" the competition with this system. You can be taught extra about these concepts right here.


Many of us puzzled if XGT batteries would be backward appropriate with the 18V system and the answer to that is no. These are two separate methods and the packs have a design that makes them unimaginable to switch for each other.

Ergonomics

Makita didn’t make many changes to the feel and appear of this hammer drill. It’s nonetheless effectively-balanced and has glorious handle ergonomics to maintain the snug grip you’re used to.


By way of weight, the GPH01 weighs 3.7 pounds bare and 5.3 pounds with its 2.5Ah battery. That’s just 0.3 pounds greater than the XPH14 with a 5.0Ah battery. Keep in mind these two batteries have the same 90Wh capacity.


It’s nonetheless a compact drill for its performance degree as nicely. At 7 1/8 inches lengthy, it’s inside a 1/4-inch of the XPH14 and slightly skinnier by means of the middle.

Kickback Control

The GPH01 introduces Active Feedback Technology (kickback control) for Makita’s drill driver/hammer drill lineup. Like many drills which have this feature, the motor mechanically shuts down when it senses the bit bind, and the drill twists about 90°. What’s unusual is that it’s not a tough cease. Instead, it’s extra of a quick deceleration.

Electronic Clutch

In a very new characteristic, the clutch moves from a collar close to the chuck to a dial on the foot. There’s a special variety of settings depending on what gear you’re in as well. Low gear has forty one settings and excessive gear has 21. It’s a really completely different feel when you’re using it. With a mechanical clutch, you feel the chuck slip over as it because the motor continues to show. With Makita’s design, it just stops.


- All-metal chuck

- Reinforced gear housing

- Dual-fan cooling Rapid Charger absolutely costs in 28 minutes or much less


Makita 40V Max XGT Hammer Drill Review Price


When it comes to price, drill bits there is a premium to maneuver up to the upper efficiency and know-how of the XGT mannequin. The bare device is $209 and a kit with two 2.5Ah batteries and a single port Rapid Charger is $399. That’s $60 - $80 greater than the comparable XPH14 options.

The guarantee is similar as the 18V line-3 years on the tool, batteries, and charger.

Makita GPH01 Vs XPH14 Hammer Drill Quick Comparison


XGT is ultimately about increased-efficiency instruments that profit from increased voltage battery packs. Once you get to these tools, it’s good to know Makita additionally makes some companion instruments like the GPH01 hammer drill that allow you to reach for a tool on the same battery platform relatively than having to carry around two totally different programs. Plus, you get legitimately higher performance and technology from the XGT model. Chances are you'll even find the same factor we're-that there are tools on both strains that make sense for the work you do. Either way, you win.